Concrete Testing Instruments

We offer Cube Moulds, Cylindrical Moulds and Beam Moulds of various sizes as listed below.
Meets: - IS: 10086, IS: 516, BS: 1881, ASTM C192, ASTM C31
Note: - All below mention Mould are also available in MILD STEEL

These moulds are made of cast iron/M.S and are supplied complete with base plate for conducting the flexural strength test of concrete.
The following sizes are available

• 100 mm x 100 mm x 500 mm size
• 150 mm x 150 mm x 700 mm size
• 150 mm x 150 mm x 750 mm size

Made of Steel, 25 mm x 25 mm square ramming face, 400 mm long, and 2 kg in weight for use with Beam Moulds

These moulds are made of cast iron and are supplied complete with base plate for conducting the compression test of concrete.
The following sizes are available.

• Cast Iron, 50 mm
• Cast Iron, and 70.6mm,
• Cast Iron, 100 mm, 8 kg
• Cast Iron, 100 mm, 10 kg
• Cast Iron, 150 mm, weight 8 Kg,10 Kg,14 Kg,18 Kg
• Cast Iron, 150 mm ISI mark
• Cast Iron, 200 mm,
• Cast Iron, 300 mm M. Steel, 300mm

Steel, and 16 mm dia x 600 mm length rounded at the lower end for use with Cube and Cylinder

These moulds are made of cast Iron and split into two parts longitudinally. These are supplied complete with a base plate for conducting the compression test of concrete.
The following sizes are available.

• Cast Iron 100 mm dia. x 100 mm high
• Cast Iron 100 mm dia. x 150 mm high
• Cast Iron 100 mm dia. x 200 mm high
• Cast Iron 150 mm dia. x 150 mm high
• Cast Iron 150 mm dia. x 300 mm high
• Cast Iron 300 mm dia. x 300 mm high

Steel, and 16 mm dia x 600 mm length rounded at the lower end for use with Cube and Cylinder

This is for used for casting cement for tensile strength tests. It is a two part split mould made of gun metal. Two thumb screws facilitate easy and quick assembling and dismantling of the mould. Supplied with base plate.
Meets:- IS: 269-1958, BS: 12, ASTM C190, ASTM C307
The following options are available.

• Briquette Mould, Single Gang
• Briquette Mould, Three Gang
• Base Plate, M. Steel, for Briquette mould

These concrete mixers are ideal for use in laboratory for mixing any semi liquid materials. All works on 220 V, 50 Hz, and single phase
The following capacities are available

• Concrete Mixer, Capacity 1 cubic feet
• Concrete Mixer, Capacity 150 litre
• Concrete Mixer, Capacity 40 litre ,65 litre (Pan Type),

Note: - Other sizes are also available.

The Flow Table is designed for determining the workability of Portland cement concrete. The Flow Table top is 76.2 cm dia, finely machined from a solid brass casting. The integral cast ribs are designed for support and strength. The stand is fabricated out of cast iron and is of sturdy construction. Holes for mounting of foundations are drilled in the base plate. The ground and hardened steel cam is designed to drop the table by 12.5 mm. Motorised having tabletop 25 cm made of M. Steel with an electric motor suitable for operation with 230 volts, 50 Hz, and single phase, AC Supply.
Meets:- IS: 1199, ASTM C124, AASHO T120, and T126

The proving rings are made of special steel, carefully forged to give maximum strength and machined to give high sensitivity commensurate with stability, ensuring long life and accuracy. Loading pads have female threading 1/2" BSF (16 tpi).. The rings are supplied complete with Works Calibration Chart, individually packed in polished wooden boxes. Proving rings to meet special requirements are also available on request. Separate polished and ground pair of Loading Pads for Compression Proving Rings and pair of Shackles for Tension Proving Rings are provided, to suit each proving ring, at extra cost
Proving ring of various Sizes are as follows:
Proving Rings Compression Type

Proving Ring 2 kN

Proving Ring 5 kN

Proving Ring 20kN

Proving Ring 25kN

Proving Ring 50kN

Proving Ring 100kN

Proving Ring 2000KN

Proving Ring 3000kN
Note: - Dial Gauge is not the standard part of Proving Ring.